Saturday, June 4, 2016
YAMAHA DIGITAL SOUND PROJECTOR - YSP-1000 - firmware update - self diagnostic menu – SMPS Power supply board schematic – FAN3641 - Audio system repair and service
Category: Audio System Repair and Service
Contents of this article
- Firmware Update Procedure
- Self Diagnostics
- SMPS Power supply Schematic
YAMAHA YSP-1000
UPDATING FIRMWARE
After replacing the following parts with the replacement parts, update the firmware. IC11 of P.C.B. ASS’Y DSP : X6962B00 ... Writing of DSP
IC17 of P.C.B. ASS’Y DSP : X7073B00 ... Writing of DSP APPLICATION / SPID
IC26 of P.C.B. ASS’Y DSP : X6894A00 ... Writing of CPU
Required tools
DOS/V machine, OS: Windows 98/2000/Me/XP, PC with a serial port (RS232C)
Program upgrading program
There are 2 program upgrading programs.
Writing of CPU : DSP_FLASHER(YSP).exe
Writing of DSP : DSP_FLASHER(YSP).exe
Writing of DSP APPLICATION / SPID
spDownloader_2_0_x_xxx.exe.
Firmware
Be sure to put following 4 firmwares in the same folder.
CPU ..... SA2_10Vx.mot
DSP ...... YSPx00_verxxxx.hex
DSP APPLICATION ...... ysp2app_YSP2-0_xxxxx_.hex
SPID ........ Y10xxxxxx.bin
IC17 of P.C.B. ASS’Y DSP : X7073B00 ... Writing of DSP APPLICATION / SPID
IC26 of P.C.B. ASS’Y DSP : X6894A00 ... Writing of CPU
Required tools
DOS/V machine, OS: Windows 98/2000/Me/XP, PC with a serial port (RS232C)
Program upgrading program
There are 2 program upgrading programs.
Writing of CPU : DSP_FLASHER(YSP).exe
Writing of DSP : DSP_FLASHER(YSP).exe
Writing of DSP APPLICATION / SPID
spDownloader_2_0_x_xxx.exe.
Firmware
Be sure to put following 4 firmwares in the same folder.
CPU ..... SA2_10Vx.mot
DSP ...... YSPx00_verxxxx.hex
DSP APPLICATION ...... ysp2app_YSP2-0_xxxxx_.hex
SPID ........ Y10xxxxxx.bin
Preparation and precautions before starting the operation
# Download DSP_FLASHER(YSP).exe and spDownloader_2_0_x_xxx.exe from the specified source to the PC being used.
# Prepare the above specified RS232C cross cable.
# While writing, keep the other application software on the PC closed. It is also recommended to keep the software on the task tray closed as well
# Download DSP_FLASHER(YSP).exe and spDownloader_2_0_x_xxx.exe from the specified source to the PC being used.
# Prepare the above specified RS232C cross cable.
# While writing, keep the other application software on the PC closed. It is also recommended to keep the software on the task tray closed as well
Operation Procedure
Writing of CPU
1. Install DSP_FLASHER(YSP).exe into the PC.
2. Before turning on the power to YSP-1000 and PC, connect between RS232C ports with the RS232C cable
2. Before turning on the power to YSP-1000 and PC, connect between RS232C ports with the RS232C cable
3. While pressing the reset switch of YSP-1000, connect the power cable to the AC outlet.
* Use a fine tipped pin or the like to push the reset switch.
4. Start up DSP_FLASHER(YSP).exe, the screen will appear
* Use a fine tipped pin or the like to push the reset switch.
4. Start up DSP_FLASHER(YSP).exe, the screen will appear
5. Select the data to be transmitted and port.
MOT FILE
Select “SA2_10Vx.mot”.
RS232C
Select the port of RS-232C.
MOT FILE
Select “SA2_10Vx.mot”.
RS232C
Select the port of RS-232C.
The port selection varies depending on OS of the PC.
Windows 98/2000/Me .......... COM1~4
Windows XP ......................... COM1~2
As no port other than the above can be used, select the port using the setting of the PC.
Windows 98/2000/Me .......... COM1~4
Windows XP ......................... COM1~2
As no port other than the above can be used, select the port using the setting of the PC.
6. Press the [E.P.] button and start writing.
7. When the program transmission is completed, the screen appears .
Then press the [OK] button to end the procedure.
8. Disconnect the power cable of YSP-1000 from the AC outlet
Writing of DSP
1. Install DSP_FLASHER(YSP).exe into the PC.
2. Before turning on the power to YSP-1000 and PC, connect between RS232C ports with the RS232C cable
2. Before turning on the power to YSP-1000 and PC, connect between RS232C ports with the RS232C cable
3. Start up DSP_FLASHER(YSP).exe, the screen will appear.
4. Select “YSP DSP” Tag.
5. Select the data to be transmitted and port.
DSP HEX FILE
Select “YSPx00_verxxxx.hex”.
RS232C
Select the port of RS-232C.
5. Select the data to be transmitted and port.
DSP HEX FILE
Select “YSPx00_verxxxx.hex”.
RS232C
Select the port of RS-232C.
The port selection varies depending on OS of the PC.
Windows 98/2000/Me .......... COM1~4
Windows XP ......................... COM1~2
As no port other than the above can be used, select the port using the setting of the PC.
Windows 98/2000/Me .......... COM1~4
Windows XP ......................... COM1~2
As no port other than the above can be used, select the port using the setting of the PC.
6. Press the [RDY] button.
7. Connect the power cable of YSP-1000 to the AC outlet. While pressing the “VOL+” key and “VOL-” key of the YSP-1000, press the “STANDBY/ON” key of the remote control to activate the DIAG function.
a. Using the “UP” or “DOWN” key of the remote control, select the DIAG menu
b. Using the “LEFT” or “RIGHT” key of the remote control, select the DIAG sub-menu.
c. Using the “ENTER” key of the remote control, make a change.
8. When the program transmission is completed, the screen appears.
9. Check the SUM.
After downloading successfully, the value of “SUM from SET” is appeared.
The procedure is completed when the value is obtained for “SUM from FILE” and “SUM from SET”.
After downloading successfully, the value of “SUM from SET” is appeared.
The procedure is completed when the value is obtained for “SUM from FILE” and “SUM from SET”.
10.Press the “STANDBY/ON” key of the YSP-1000 to turn off the power.
Writing of DSP APPLICATION / SPID
1. Install spDownloader_2_0_x_xxx.exe into the PC.
2. Before turning on the power to YSP-1000 and PC, connect between RS232C ports with the RS232C cable (cross cable). (Fig. 1)
3. Connect the power cable of YSP-1000 to the AC outlet.
While pressing the “VOL+” key and “VOL-” key of the YSP-1000, press the “STANDBY/ON” key of the remote control to activate the DIAG function.
2. Before turning on the power to YSP-1000 and PC, connect between RS232C ports with the RS232C cable (cross cable). (Fig. 1)
3. Connect the power cable of YSP-1000 to the AC outlet.
While pressing the “VOL+” key and “VOL-” key of the YSP-1000, press the “STANDBY/ON” key of the remote control to activate the DIAG function.
a. Using the “UP” or “DOWN” key of the remote control, select the DIAG menu
b. Using the “LEFT” or “RIGHT” key of the remote control, select the DIAG sub-menu.
c. Using the “ENTER” key of the remote control, make a change.
d. For restarting, use the “STANDBY/ON” key of the YSP-1000 or the remote control.
4. Start up spDownloader_2_0_x_xxx.exe, the screen will appear.
5. Select the data to be transmitted and port.
COM Port
Select the port of RS-232C.
D/load Protocol
Select “SPCM Protocol”
COM Port
Select the port of RS-232C.
D/load Protocol
Select “SPCM Protocol”
6. Select Firmware and execute writing as follows. First, select DSP APPLICATION and perform steps a to e for writing.
Then, select SPID and perform steps a to d for writing.
Then, select SPID and perform steps a to d for writing.
a. Press the button beside the Source firmware Box.
And select the firmware.
# DSP APPLICATION : ysp2app_YSP2-0_xxxxx_.hex
# SPID : Y10xxxxxx.bin.
And select the firmware.
# DSP APPLICATION : ysp2app_YSP2-0_xxxxx_.hex
# SPID : Y10xxxxxx.bin.
b. Confirm Software Target and press the [Download] button.
* When Source filename is selected, Software Target box is selected automatically.
* If Software Target is different, confirm again Source filename or re-open spDownloader.
* If Software Target is different, confirm again Source filename or re-open spDownloader.
c. After downloading sccessfully, “Downloaded ‘*****’ OK” is appeared. Confirm “FLASH Write ok” on the Serial Log window.
d. Press the [Done] button.
e. For restarting, use the “STANDBY/ON” key of the YSP-1000 or the remote control.
f. The display returns to screen (1).
Select SPID and perform steps a to d for writing.
e. For restarting, use the “STANDBY/ON” key of the YSP-1000 or the remote control.
f. The display returns to screen (1).
Select SPID and perform steps a to d for writing.
7. Press the “STANDBY/ON” key of the YSP-1000 to turn off the power.
8. While pressing the “VOL+” key and “VOL-” key of the YSP-1000, press the “STANDBY/ON” key of the remote control to activate the DIAG function.
8. While pressing the “VOL+” key and “VOL-” key of the YSP-1000, press the “STANDBY/ON” key of the remote control to activate the DIAG function.
a. Using the “UP” or “DOWN” key of the remote control, select the DIAG menu.
b. Using the “LEFT” or “RIGHT” key of the remote control, select the DIAG sub-menu.
c. Using the “RETURN” key of the remote control, make a change.
d. Check the version of the firmware.
Using the “LEFT” key or “RIGHT” key of the remote control, have the DIAG menu displayed.
Using the “LEFT” key or “RIGHT” key of the remote control, have the DIAG menu displayed.
The procedure is completed when the same version shows.
9. Press the “STANDBY/ON” key of the YSP-1000 to turn off the power..
SELF DIAGNOSIS FUNCTION
Starting DIAG
To activate the DIAG function, press the “STANDBY/ON” key of the remote control while pressing V+ and V- keys of the main unit at the same time.
To activate the DIAG function, press the “STANDBY/ON” key of the remote control while pressing V+ and V- keys of the main unit at the same time.
Starting DIAG in the protection cancel mode
If the protection function works and causes hindrance to trouble diagnosis, cancel the protection function as described below, and it will be possible to enter the DIAG mode.
Press the “STANDBY/ON” key while simultaneously pressing those two keys indicated in the figure above. At this time, keep pressing those two keys for 3 seconds or longer. In this mode, the “SLEEP” segment of the FL display of the main unit flashes to indicate that the mode is DIAG mode with the protection functions disabled.
If the protection function works and causes hindrance to trouble diagnosis, cancel the protection function as described below, and it will be possible to enter the DIAG mode.
Press the “STANDBY/ON” key while simultaneously pressing those two keys indicated in the figure above. At this time, keep pressing those two keys for 3 seconds or longer. In this mode, the “SLEEP” segment of the FL display of the main unit flashes to indicate that the mode is DIAG mode with the protection functions disabled.
Canceling DIAG
1. Before canceling DIAG, execute setting for PRESET of DIAG menu No.8 (Memory initialization inhibited or Memory initialized). * In order to keep the user memory stored, be sure to select PRESET INHIBIT (Memory initialization inhibited). Any protection history will remain in memory.
2. Turn off the power by pressing the “STANDBY/ON” key of the main unit or the “STANDBY” key of the remote control.
1. Before canceling DIAG, execute setting for PRESET of DIAG menu No.8 (Memory initialization inhibited or Memory initialized). * In order to keep the user memory stored, be sure to select PRESET INHIBIT (Memory initialization inhibited). Any protection history will remain in memory.
2. Turn off the power by pressing the “STANDBY/ON” key of the main unit or the “STANDBY” key of the remote control.
Display provided when DIAG started
When the monitor is connected, DIAGNOSTIC MENU appears on its screen as shown in the figure. (It remains on display until DIAG is cancelled.)
When the monitor is connected, DIAGNOSTIC MENU appears on its screen as shown in the figure. (It remains on display until DIAG is cancelled.)
The FL display of the main unit displays the protection function history data and the version (1 alphabet) and the DIAG menu [sub-menu (THR ALL) of DIAG menu No.1 DSP THROUGH] a few seconds later.
Operation procedure of DIAG menu and SUB-MENU
There are 14 MENU items, each of which has some SUBMENU items.
DIAG menu selection
Select the DIAG menu by using the UP/DOWN
(Reverse) (Forward) key of the remote control.
SUB-MENU selection
Select the DIAG sub-menu by using the LEFT/RIGHT (Reverse) (Forward) keys.
There are 14 MENU items, each of which has some SUBMENU items.
DIAG menu selection
Select the DIAG menu by using the UP/DOWN
(Reverse) (Forward) key of the remote control.
SUB-MENU selection
Select the DIAG sub-menu by using the LEFT/RIGHT (Reverse) (Forward) keys.
Functions in DIAG mode
In addition to the DIAG menu items, functions as listed
below are available.
#Input selection
# Muting
# Night
# Power on/off
# Master volume
Functions related to the set menu are not available.
In addition to the DIAG menu items, functions as listed
below are available.
#Input selection
# Muting
# Night
# Power on/off
# Master volume
Functions related to the set menu are not available.
POWER SUPPLY BOARD SCHEMATIC
USING FAN4631
CLICK ON THE IMAGE TO ZOOM IN
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment