Tuesday, June 28, 2016
Sony PlayStation 3 - Sony PS3 – How to replace the BluRay Laser - KES-4000AAA - How to remove the case how to remove the laser eye unit – Laptop repair and service
Category: Laptop Repair and Servcie
Contents of this article
- How to remove the top cover
- How to remove the Blu Ray Drive
- How to replace the Laser unit
Sony PlayStation 3
HOW TO REPLACE THE LASER PICKUP UNIT
Use the tip of a spudger to remove the black rubber screw cover from the side of the PS3.
The screw cover may be underneath a warranty sticker. This sticker will change appearance, and show "VOID" after it has been removed.
The screw cover may be underneath a warranty sticker. This sticker will change appearance, and show "VOID" after it has been removed.
Remove the single 8.5 mm T10 Security Torx screw from the smart plate.
Pull the smart plate toward the hard drive bay, then lift it off the body of the PS3.
Be sure to keep track of the small metal bracket loosely held in the top cover, if equipped.
Remove the following seven screws:
Six 52 mm Phillips screws
One 30 mm Phillips screw
Lift the top cover from its rear edge and rotate it toward the front of the PS3.
Remove the top cover.
One 30 mm Phillips screw
Lift the top cover from its rear edge and rotate it toward the front of the PS3.
Remove the top cover.
Disconnect the Blu-ray power cable from the motherboard.
Pull the connector straight up and out of its socket.
Lift the Blu-ray drive from the edge nearest the power supply and rotate it away from the chassis enough to access its ribbon cable.
Lift the Blu-ray drive from the edge nearest the power supply and rotate it away from the chassis enough to access its ribbon cable.
Use your fingernail to flip up the retaining flap on the Blu-ray ribbon cable socket.
Be sure you are prying up on the retaining flap, not the socket itself.
Pull the ribbon cable out of its socket.
Remove the Blu-ray drive from the PS3.
If replacing the Blu-ray drive, transfer the power cable to your new drive.
Pull the ribbon cable out of its socket.
Remove the Blu-ray drive from the PS3.
If replacing the Blu-ray drive, transfer the power cable to your new drive.
A2 ribbon cable was removed in
Step 9 of the previous guide. Now remove ribbon cables A3, A4, A5 and A6 by using your fingernail to flip open the ribbon flaps.
With a Ph#00 screwdriver remove screws 9, 10, 11, 12 and 13.
Note that screws 11 & 13 are fastening a stabiliser on some models. These are pictured in the third photo in step 9, and you will need to recall their position for reassembly.
With a Ph#00 screwdriver remove screws 9, 10, 11, 12 and 13.
Note that screws 11 & 13 are fastening a stabiliser on some models. These are pictured in the third photo in step 9, and you will need to recall their position for reassembly.
With extreme caution move the BluRay control board in a flipping motion by moving the left side of the controller upwards levering towards the right. Keep the right side of the controller close to the BluRay drive as the red and black A7 cable is delicate.
Remove cable A7 which is the cable that links the PS3s disc drive eject detector to the control board.
Remove screws 14 and 15.
Part C is a stabilizer and grounding contact to help absorb movement while the Blu-ray drive is in use.
This may be located in a different area of your drive as decided by the manufacturer. There may also be additional ones. Make sure when reassembling to put this stabilizer back in the same place as it is originally found even if it is not found in exactly the same location as this article. Failure to do so could result in disc scratching.
Remove the silver coloured drive cover.
This may be located in a different area of your drive as decided by the manufacturer. There may also be additional ones. Make sure when reassembling to put this stabilizer back in the same place as it is originally found even if it is not found in exactly the same location as this article. Failure to do so could result in disc scratching.
Remove the silver coloured drive cover.
Remove screws 16, 17, 18, 19 and 20.
Remove magnetic spindle D.
Remove top of drive being careful again not to damage the red and black cable.
Remove screws 21 and 22 and the brackets they hold in place.
Now remove bar E.
Unclip ribbon F.
Remove and replace Laser
Assemble G with new Laser Assembly.
Follow this article in reverse to reassemble.
Remove top of drive being careful again not to damage the red and black cable.
Remove screws 21 and 22 and the brackets they hold in place.
Now remove bar E.
Unclip ribbon F.
Remove and replace Laser
Assemble G with new Laser Assembly.
Follow this article in reverse to reassemble.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment