Tuesday, June 21, 2016
SONY KLV-40X300A - KLV-46X300A - KLV-52X300A - Service mode - Power LED blinking codes and causes - Service mode alignment and adjustment - LCD television repair and service - Tpis manual
Category: LCD Television Repair and Service
Contents of this article
- How to access to service mode
- LED blinking codes
- Service adjustments
- Shipping mode
SONY KLV-40X300A - KLV-46X300A - KLV-52X300A
SERVICE MODE
Entering Service Mode
1. Push “i+ (info)”, “5”, “Volume+” then “TV button”with remote commander.
2. Service mode menu will appear on display.
Change Setting Data for TV
1. Press “2 / 5”on remote commander to select (up / down) category.
2. Press “1 / 4”on remote commander to select (up / down) Item.
3. Press “3 / 6”on remote commander to change (up / down) data.
1. Push “i+ (info)”, “5”, “Volume+” then “TV button”with remote commander.
2. Service mode menu will appear on display.
Change Setting Data for TV
1. Press “2 / 5”on remote commander to select (up / down) category.
2. Press “1 / 4”on remote commander to select (up / down) Item.
3. Press “3 / 6”on remote commander to change (up / down) data.
Write data for TVM
1. Press “Mute” on remote commander. It shows green “SERVICE” changes to green “WRITE”.
2. Press “0” on remote commander. Green “WRITE” changes to red “WRITE”. It indicates writing processing.
3. After for 1 minute, red “WRITE” changes to green “SERVICE”. Writing process is done at this point.
1. Press “Mute” on remote commander. It shows green “SERVICE” changes to green “WRITE”.
2. Press “0” on remote commander. Green “WRITE” changes to red “WRITE”. It indicates writing processing.
3. After for 1 minute, red “WRITE” changes to green “SERVICE”. Writing process is done at this point.
Entering BEM service menu
1. Press “Previous channel” on remote commander.
Change Setting Data for BEM
1. Press “2/5” on remote commander to select (up / down) category.
2. Press “1/4” on remote commander to select (up / down) Item.
3. Press “3/6” on remote commander to change (up / down) data.
1. Press “Previous channel” on remote commander.
Change Setting Data for BEM
1. Press “2/5” on remote commander to select (up / down) category.
2. Press “1/4” on remote commander to select (up / down) Item.
3. Press “3/6” on remote commander to change (up / down) data.
Write data for BEM
1. Press “Mute” on remote commander. It shows green “SERVICE” changes to
green “WRITE”.
2. Press “0” on remote commander. Green “WRITE” changes to red “WRITE”. It indicates writing processing.
3. After for few second, red “WRITE” changes to green “SERVICE”. Writing process is done at this point.
1. Press “Mute” on remote commander. It shows green “SERVICE” changes to
green “WRITE”.
2. Press “0” on remote commander. Green “WRITE” changes to red “WRITE”. It indicates writing processing.
3. After for few second, red “WRITE” changes to green “SERVICE”. Writing process is done at this point.
How to change shipping condition.
1. During service mode, press “8” on remote commander.
2. Press “mute” on remote commander.
3. Press “0” on remote commander.
4. Display change to “SERVICE” “RST-” “RST-EXE” “RST-EXE”
1. During service mode, press “8” on remote commander.
2. Press “mute” on remote commander.
3. Press “0” on remote commander.
4. Display change to “SERVICE” “RST-” “RST-EXE” “RST-EXE”
SELF DIAGNOSIS
If an error occurs, the STANDBY LED will automatically begin to flash. The number of times the LED flashes translates to a probable source of the problem.
A definition of the STANDBY LED flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
A definition of the STANDBY LED flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
DIAGNOSTIC TEST INDICATION
When an error occurs, the STANDBY LED will flash a set number of times to indicate the possible cause of the problem. If there is more than one error, the LED will identify the first of the problem areas. Result for all of the following diagnostic items are displayed on screen. If the screen displays a “0”, no error has occurred .
When an error occurs, the STANDBY LED will flash a set number of times to indicate the possible cause of the problem. If there is more than one error, the LED will identify the first of the problem areas. Result for all of the following diagnostic items are displayed on screen. If the screen displays a “0”, no error has occurred .
POWER LED BLINKING CODES AND CAUSES
| Number of times STANDY LED (Red) flashes | Monitoring Items (Screen Display) | Diagnostic Item Description |
| 2 times | POW OVP | Main Power Over Voltage Protection |
| 3 times | POW ERR1 | Power Error |
| 5 times | T_CON | T_CON Error |
| 6 times | BACKLITE | Back Light Error (Panel Inverter) |
| 7 times | TEMP ERR | Temperature Abnormal Detection |
| 8 times | AUD PROT | Audio Abnormal Detection |
| 9 times | FAN_ERR | FAN Error (Not Detected. Display Only) |
| 13 times | BALANCER | Panel Balancer Error |
STOPPING THE STANDBY FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY lamp from flashing.
SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to
bring up past occurrences of failure for confirmation on the screen:
To Bring Up Screen Test
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to
bring up past occurrences of failure for confirmation on the screen:
To Bring Up Screen Test
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
DISPLAY > DIGIT 5 > VOLUME + BUTTON > POWER ON
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen. After you have completed the repairs, clear the result display to “0”.
Quitting Self-diagnostic screen
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
Quitting Self-diagnostic screen
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
TO INSERT THE CONNECTOR
The connector might not be properly locked when only pressed from the middle.
Be sure to press both sides to confirm it is property locked.
The connector might not be properly locked when only pressed from the middle.
Be sure to press both sides to confirm it is property locked.
1. Press the middle part of the connecto to insert till it locks.
2. Press the right side to confirm it is locked.
3. Press the left side to confirm it is locked.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment