Tuesday, June 28, 2016
Panasonic - PT-DZ6710U - PT-DZ6700U - PT-DW6300US - PT-D6000US – How to enter to service mode – Service mode options – Disassembling procedure – How to remove the case – RS232 communication setting - Projector repair and service
Category: Projector Repair and Servcie
Contents of this article
- How to Access service mode
- RS232 communication setting
- How to remove the case
Panasonic - PT-DZ6710U - PT-DZ6700U - PT-DW6300US - PT-D6000US
Service Mode
This projector has Serviceman Mode in addition to standard on-screen menus (User Mode).
Setting to Service Mode
(1) Press the MENU button.
The MAIN MENU screen will appear.
(2) Select “PROJECTOR SETUP” using the UP or DOWN buttons and press the ENTER button.
The PROJECTOR SETUP screen will appear.
(3) Select “SERVICE PASSWORD” using the UP or DOWN buttons and press the ENTER button.
The SERVICE PASSWORD screen will appear.
(4) Input the password "1565" by remote control and press the ENTER button.
Note:
# Asterisk (*) will appear for the password numbers.
This projector has Serviceman Mode in addition to standard on-screen menus (User Mode).
Setting to Service Mode
(1) Press the MENU button.
The MAIN MENU screen will appear.
(2) Select “PROJECTOR SETUP” using the UP or DOWN buttons and press the ENTER button.
The PROJECTOR SETUP screen will appear.
(3) Select “SERVICE PASSWORD” using the UP or DOWN buttons and press the ENTER button.
The SERVICE PASSWORD screen will appear.
(4) Input the password "1565" by remote control and press the ENTER button.
Note:
# Asterisk (*) will appear for the password numbers.
(5) Press the MENU button.
"SERVICEMAN MODE" (MAIN MENU) will be displayed.
"SERVICEMAN MODE" (MAIN MENU) will be displayed.
Resetting to User Mode
(1) Press the MENU button.
The MAIN MENU screen will appear.
(2) Select “PROJECTOR SETUP” using the UP or DOWN buttons and press the ENTER button.
The PROJECTOR SETUP screen will appear.
(3) Select SERVICE PASSWORD using the UP or DOWN buttons and press the ENTER button.
The SERVICE PASSWORD screen will appear.
(1) Press the MENU button.
The MAIN MENU screen will appear.
(2) Select “PROJECTOR SETUP” using the UP or DOWN buttons and press the ENTER button.
The PROJECTOR SETUP screen will appear.
(3) Select SERVICE PASSWORD using the UP or DOWN buttons and press the ENTER button.
The SERVICE PASSWORD screen will appear.
(4) Input the password "0000" by remote control and press the ENTER button.
Note:
# Asterisk (*) will appear for the password numbers.
(5) Press the MENU button.
"USER MODE" (MAIN MENU) will be displayed.
Note:
# Asterisk (*) will appear for the password numbers.
(5) Press the MENU button.
"USER MODE" (MAIN MENU) will be displayed.
Functions in Service Mode
EXTRA OPTION
"EXTRA OPTION" is added to the MENU.
EXTRA OPTION
"EXTRA OPTION" is added to the MENU.
CUT OFF
Sets the display ON/OFF for each color (R, G, B).
3DCMS
Sets ON (Valid) / OFF (Invalid) of 3DCMS.
SELF CHECK
Displays SELF CHECK.
Sets the display ON/OFF for each color (R, G, B).
3DCMS
Sets ON (Valid) / OFF (Invalid) of 3DCMS.
SELF CHECK
Displays SELF CHECK.
CW INDEX
When the color wheel is replaced, adjusts it with LEFT and RIGHT buttons.
a. Display the test pattern (Red & Blue pattern).
b. Confirm whether there is a horizontal line.
c. If a horizontal line is in the red area, decrease CW INDEX setting value by 1, and record the value where the horizontal line.
(in both red area and blue area) disappears. (The recorded value is assumed to "A".)
d. If a horizontal line is in the blue area, increase CW INDEX setting value by 1, and record the value where the horizontal line.
(in both red area and blue area) disappears. (The recorded value is assumed to "B".)
e. Set the mean value (omission below decimal point) of "A" and "B" to the CW INDEX setting value.
When the color wheel is replaced, adjusts it with LEFT and RIGHT buttons.
a. Display the test pattern (Red & Blue pattern).
b. Confirm whether there is a horizontal line.
c. If a horizontal line is in the red area, decrease CW INDEX setting value by 1, and record the value where the horizontal line.
(in both red area and blue area) disappears. (The recorded value is assumed to "A".)
d. If a horizontal line is in the blue area, increase CW INDEX setting value by 1, and record the value where the horizontal line.
(in both red area and blue area) disappears. (The recorded value is assumed to "B".)
e. Set the mean value (omission below decimal point) of "A" and "B" to the CW INDEX setting value.
POWER ON SHUTTER
# OPEN: Opens the shutter when power ON.
# CLOSE: Closes the shutter when power ON.
POWER OFF SHUTTER
# IGNORE: Does not control the shutter when power OFF.
# OPEN: Opens the shutter when power OFF.
# CLOSE: Closes the shutter when power OFF.
# OPEN: Opens the shutter when power ON.
# CLOSE: Closes the shutter when power ON.
POWER OFF SHUTTER
# IGNORE: Does not control the shutter when power OFF.
# OPEN: Opens the shutter when power OFF.
# CLOSE: Closes the shutter when power OFF.
MODEL
Set it when the A-P.C.Board is replaced.
# If replacing A-P.C.Board (assembly), set MODEL.
* Never set it to a model name different from the model that installs the new A-P.C.Board. If a different model name is set, it becomes impossible to output normal pictures after the next startup.
* When a new A-P.C.Board is installed without maintenance of adjustment data, it is required to adjust the color wheel.
ACF
Executes ACF setting/operation.
# FILTER SETUP: Sets the interval time of automatic rewinding of the filter.
# ROLL: Rewinds the filter once compulsorily.
CLOG SENSOR CALIBRATION
Execute the sensor calibration when EEPROM (IC3103 or IC3104) / A-P.C.Board or Airflow sensor (CF1302) is replaced.
* Make the main unit to the assembled state without fail, set the projector to the floor installation, and calibrate.
* If the projector installed at an elevation of 1 400 m or higher sea level, be sure to set the HIGH ALTITUDE MODE sub-menu in PROJECTOR SETUP menu to ON, and attempt the calibration.
Set it when the A-P.C.Board is replaced.
# If replacing A-P.C.Board (assembly), set MODEL.
* Never set it to a model name different from the model that installs the new A-P.C.Board. If a different model name is set, it becomes impossible to output normal pictures after the next startup.
* When a new A-P.C.Board is installed without maintenance of adjustment data, it is required to adjust the color wheel.
ACF
Executes ACF setting/operation.
# FILTER SETUP: Sets the interval time of automatic rewinding of the filter.
# ROLL: Rewinds the filter once compulsorily.
CLOG SENSOR CALIBRATION
Execute the sensor calibration when EEPROM (IC3103 or IC3104) / A-P.C.Board or Airflow sensor (CF1302) is replaced.
* Make the main unit to the assembled state without fail, set the projector to the floor installation, and calibrate.
* If the projector installed at an elevation of 1 400 m or higher sea level, be sure to set the HIGH ALTITUDE MODE sub-menu in PROJECTOR SETUP menu to ON, and attempt the calibration.
When OK is selected and ENTER button is pressed, the calibration is executed.
# When the calibration is started, the screen becomes whole magenta.
# While calibrating, all lamps will light (DUAL mode).
# Do not switch OFF the projector while calibrating.
# When the magenta screen will disappear in approx. 15 minutes and it returns to the normal screen, the calibration is completed.
# Turn the POWER switch OFF and turn ON it again, then confirm whether to operate normally.
Ye MODULATE Addition
When the PICTURE MODE menu is displayed, it is enabled to be adjusted with the ENTER button.
# ON: Validates Ye MODULATE function.
# OFF: Invalidates Ye MODULATE function.
ADVANCED MENU Addition
The following 4 items are added to the ADVANCED MENU.
1. FRAME LOCK
When the input signal is RGB, FRAME LOCK is added.
2. 480i SD
When non-standard signal of 480i/576i is inputted (AV amplifier, etc.), synchronization might be disordered according to connected equipment. In this case, set 480i SD to ON.
3. 480p OS
When 480p/576p is received, aliasing noise (longitudinal striated beat noise) might be generated according to connected equipment. In this case, set 480p OS to ON. However, the resolution decreases a little.
# When the calibration is started, the screen becomes whole magenta.
# While calibrating, all lamps will light (DUAL mode).
# Do not switch OFF the projector while calibrating.
# When the magenta screen will disappear in approx. 15 minutes and it returns to the normal screen, the calibration is completed.
# Turn the POWER switch OFF and turn ON it again, then confirm whether to operate normally.
Ye MODULATE Addition
When the PICTURE MODE menu is displayed, it is enabled to be adjusted with the ENTER button.
# ON: Validates Ye MODULATE function.
# OFF: Invalidates Ye MODULATE function.
ADVANCED MENU Addition
The following 4 items are added to the ADVANCED MENU.
1. FRAME LOCK
When the input signal is RGB, FRAME LOCK is added.
2. 480i SD
When non-standard signal of 480i/576i is inputted (AV amplifier, etc.), synchronization might be disordered according to connected equipment. In this case, set 480i SD to ON.
3. 480p OS
When 480p/576p is received, aliasing noise (longitudinal striated beat noise) might be generated according to connected equipment. In this case, set 480p OS to ON. However, the resolution decreases a little.
4. HPLL
When non-standard signal of VIDEO/S-VIDEO is inputted (VCR, VHD, etc.), horizontal synchronization might be disordered
according to connected equipment. In this case, set HPLL to OFF.
STATUS Addition
The following items are added to the STATUS sub-menu in PROJECTOR SETUP menu.
1. APPROXIMATE TIME
Prediction remainder time of the filter in ACF
2. FPGA VERSION
FPGA software version
3. DDP VERSION
DDP software version
4. BALLAST VERSION
Ballast software version
5. GEOMETRY VERSION
Geometry software version (PT-DZ6710* only)
6. LAMP1 ON
Number of times LAMP1 has been lit [Failure number of times]
7. LAMP2 ON
Number of times LAMP2 has been lit [Failure number of times]
8. SHUTTER
Opening and shutting number of times [Failed number of times]
9. TEMP(°C)
Intake air temperature / Exhaust air temperature / Optical module temperature
10. AIR FLOW
Sensor value / AD conversion value
11. VOLT
Voltage of LAMP1/LAMP2
12. POWER
Power fan status (Rotational speed)
13. OUT1
Exhaust 1 fan status (Rotational speed)
14. OUT2
Exhaust 2 fan status (Rotational speed)
15. LAMP1
Lamp 1 fan status (Rotational speed)
16. LAMP2
Lamp 2 fan status (Rotational speed)
17. BALLAST
Ballast fan status (Rotational speed)
18. RADIATOR
Radiator fan status (Rotational speed)
19. CW
CW fan status (Rotational speed)
20. LIQUID
Liquid cooling pump fan status (Rotational speed)
Shutter Counter Reset
SHUTTER COUNTER is added to the INITIALIZE sub-menu in PROJECTOR SETUP menu. The shutter counter can be initialized.
Procedure of Communication Condition Settings
(1) Press the MENU button.
The MAIN MENU screen will appear.
(2) Select PROJECTOR SETUP using the UP or DOWN button.
(3) Press the ENTER button.
The PROJECTOR SETUP screen will appear.
(4) Select RS-232C using the UP or DOWN button.
(5) Press the ENTER button.
The RS-232C screen will appear.
(6) Press the UP or DOWN button to select communication settings.
(7) Press the LEFT or RIGHT button to confirm the setting..
(8) Press the MENU button three times.
The on-screen indications disappear, and the system returns to the normal screen.
When non-standard signal of VIDEO/S-VIDEO is inputted (VCR, VHD, etc.), horizontal synchronization might be disordered
according to connected equipment. In this case, set HPLL to OFF.
STATUS Addition
The following items are added to the STATUS sub-menu in PROJECTOR SETUP menu.
1. APPROXIMATE TIME
Prediction remainder time of the filter in ACF
2. FPGA VERSION
FPGA software version
3. DDP VERSION
DDP software version
4. BALLAST VERSION
Ballast software version
5. GEOMETRY VERSION
Geometry software version (PT-DZ6710* only)
6. LAMP1 ON
Number of times LAMP1 has been lit [Failure number of times]
7. LAMP2 ON
Number of times LAMP2 has been lit [Failure number of times]
8. SHUTTER
Opening and shutting number of times [Failed number of times]
9. TEMP(°C)
Intake air temperature / Exhaust air temperature / Optical module temperature
10. AIR FLOW
Sensor value / AD conversion value
11. VOLT
Voltage of LAMP1/LAMP2
12. POWER
Power fan status (Rotational speed)
13. OUT1
Exhaust 1 fan status (Rotational speed)
14. OUT2
Exhaust 2 fan status (Rotational speed)
15. LAMP1
Lamp 1 fan status (Rotational speed)
16. LAMP2
Lamp 2 fan status (Rotational speed)
17. BALLAST
Ballast fan status (Rotational speed)
18. RADIATOR
Radiator fan status (Rotational speed)
19. CW
CW fan status (Rotational speed)
20. LIQUID
Liquid cooling pump fan status (Rotational speed)
Shutter Counter Reset
SHUTTER COUNTER is added to the INITIALIZE sub-menu in PROJECTOR SETUP menu. The shutter counter can be initialized.
Procedure of Communication Condition Settings
(1) Press the MENU button.
The MAIN MENU screen will appear.
(2) Select PROJECTOR SETUP using the UP or DOWN button.
(3) Press the ENTER button.
The PROJECTOR SETUP screen will appear.
(4) Select RS-232C using the UP or DOWN button.
(5) Press the ENTER button.
The RS-232C screen will appear.
(6) Press the UP or DOWN button to select communication settings.
(7) Press the LEFT or RIGHT button to confirm the setting..
(8) Press the MENU button three times.
The on-screen indications disappear, and the system returns to the normal screen.
Interlock Function
To ensure safety, the protection circuit of the main unit functions, and this projector becomes operation halt condition (a part of circuit is energizing) when the lamp unit cover is removed or installed incorrectly.
To ensure safety, the protection circuit of the main unit functions, and this projector becomes operation halt condition (a part of circuit is energizing) when the lamp unit cover is removed or installed incorrectly.
When servicing, install the lamp unit cover in former position when energizing with the upper case removed.
DISASSEMBLING PROCEDURE
Removal of Upper Case
(1) Turn the lens cover counterclockwise and remove.
(1) Turn the lens cover counterclockwise and remove.
(2) Remove the projection lens.
1. Fully turn the projection Lens counterclockwise.
2. While pressing the lens release button, turn the projection lens counterclockwise in addition.
3. Remove the projection lens.
2. While pressing the lens release button, turn the projection lens counterclockwise in addition.
3. Remove the projection lens.
(3) Loosen the 1 screw until it idles, then remove the lamp unit
cover.
Note:
The lamp unit cover is connected to the main unit with the connector. Be careful when removing it.
Note:
The lamp unit cover is connected to the main unit with the connector. Be careful when removing it.
(4) Unscrew the 5 screws and remove the upper case.
Note:
Confirm the lens release button actuates correctly when you reassemble the upper case as it was.
Confirm the lens release button actuates correctly when you reassemble the upper case as it was.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment