Sunday, June 5, 2016
LENOVO TABLET - LENOVO IdeaTab S6000 – Charger testing procedure - How to disassemble IdeaTab S6000 – Battery removal – Tablet repairs and service
Category: Tablets Repair and Service
Contents of this article
- AC adapter checking
- Back cover removal
- Battery removal
LENOVO IdeaTab S6000
To verify a fault symptom, follow the steps below:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Make sure that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Make sure that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power supply checkouts:
Checking the IdeaTab
Checking the internal
Checking the IdeaTab AC Charger
When you use the IdeaTab AC Charger to charge the tablet but no power is charged, see the instructions in this topic to check the IdeaTab AC Charger.
To check the IdeaTab AC Charger, do the following:
1. Disconnect the micro-USB cable from the tablet.
2. Measure the output voltage across the connector marked B of the micro-USB cable. Refer to the following figure:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Make sure that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Make sure that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power supply checkouts:
Checking the IdeaTab
Checking the internal
Checking the IdeaTab AC Charger
When you use the IdeaTab AC Charger to charge the tablet but no power is charged, see the instructions in this topic to check the IdeaTab AC Charger.
To check the IdeaTab AC Charger, do the following:
1. Disconnect the micro-USB cable from the tablet.
2. Measure the output voltage across the connector marked B of the micro-USB cable. Refer to the following figure:
Note: The output voltage across pin 3 of the micro-B connector might be different from the one you are servicing.
3. If the voltage is not correct, replace the micro-USB cable.
4. If the voltage is acceptable, replace the system board.
Checking the internal battery status
To check the battery status of the tablet, do either of the following:
• Approximate information about the battery status
Get the approximate status of the battery at any time by checking the battery status icon on the system bar in the upper-right corner of the screen. The
shorter the green bar is, the less the battery power remains.
• Accurate information about the battery status
To get the accurate information about the battery status of the tablet, do the following
3. If the voltage is not correct, replace the micro-USB cable.
4. If the voltage is acceptable, replace the system board.
Checking the internal battery status
To check the battery status of the tablet, do either of the following:
• Approximate information about the battery status
Get the approximate status of the battery at any time by checking the battery status icon on the system bar in the upper-right corner of the screen. The
shorter the green bar is, the less the battery power remains.
• Accurate information about the battery status
To get the accurate information about the battery status of the tablet, do the following
1. Open the Android Settings screen.
To open the Android Settings screen, do either of the following:
– From the main Home screen, touch the Android Settings icon on
Lenovo Launch Zone. The Android Settings screen is displayed.
– Touch the application icon from the action bar and then touch Settings.
The Android Settings screen is displayed.
2. Touch About Tablet on the Android Settings screen.
3. Touch Status to view the accurate percentage of the remaining battery power. You also can touch Battery use to check what applications are consuming battery power.
To open the Android Settings screen, do either of the following:
– From the main Home screen, touch the Android Settings icon on
Lenovo Launch Zone. The Android Settings screen is displayed.
– Touch the application icon from the action bar and then touch Settings.
The Android Settings screen is displayed.
2. Touch About Tablet on the Android Settings screen.
3. Touch Status to view the accurate percentage of the remaining battery power. You also can touch Battery use to check what applications are consuming battery power.
DISASSEMBLING PROCEDURE
Back cover
Figure 1. Removal steps of back cover
Use a thin flat blade to carefully pry off the two speaker covers.
Figure 1. Removal steps of back cover
Use a thin flat blade to carefully pry off the two speaker covers.
Remove screws 1.
Removal steps of back cover (continued)
Insert the thin flat blade between the frame join near the power button, then carefully move the blade along the join to remove the back cover.
Insert the thin flat blade between the frame join near the power button, then carefully move the blade along the join to remove the back cover.
Battery pack
Removal steps of battery pack
Hold the tab and lift the battery slightly. Insert a flat blade under the right side of the battery and pry the battery out. Disconnect the battery connector .
Detach the battery from the bracket, as shown below 1.
Hold the tab and lift the battery slightly. Insert a flat blade under the right side of the battery and pry the battery out. Disconnect the battery connector .
Detach the battery from the bracket, as shown below 1.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment