Monday, June 20, 2016
HEALTHSTREAM T801 Treadmill - Error codes – Causes – Solution – Treadmill repair and service
Category: Treadmill Repair and Service
Contents of this article
- Error codes
- Speed adjustment
- Pulse function
HEALTHSTREAM T801
ERROR CODE AND SOLUTION
ERROR 1. Speed sensor
Speed sensor is broken.
Main power relay is broken (in the motor controller).
Motor is broken or motor wire is badly connected.
Main power relay is broken (in the motor controller).
Motor is broken or motor wire is badly connected.
PWM circuit is broken.
Turn off and on the power. Push Stop + Slow together , and you are in setup mode.
Push Stop + Fast together in setup mode, and you are in Diagnostic mode.
Using fast, slow key to select L Er (clear last error) and push Start to clear the error.
Select SP t (Speed test)in disgnostic and push Start to test the treadmill.
Check if motor is running. If it run, - Check the value of upper right LED. if it does not run – Check motor wire connection , brush contact first and then change the motor controller.
Warning : Do not step on the treadmill, it is very dangerous.
Push Stop + Fast together in setup mode, and you are in Diagnostic mode.
Using fast, slow key to select L Er (clear last error) and push Start to clear the error.
Select SP t (Speed test)in disgnostic and push Start to test the treadmill.
Check if motor is running. If it run, - Check the value of upper right LED. if it does not run – Check motor wire connection , brush contact first and then change the motor controller.
Warning : Do not step on the treadmill, it is very dangerous.
ERROR 2. Over speed
When treadmill runs faster than target speed.
–Check power circuit. When user kicks the treadmill belt faster intentionally Frequency is very low. It usually happens during workout(14K m/h to 16Km/H).
–Check power circuit. When user kicks the treadmill belt faster intentionally Frequency is very low. It usually happens during workout(14K m/h to 16Km/H).
Turn off and on the power. Push Stop + Slow together , and you are in setup mode.
Push Stop + Fast together in setup mode, and you are in
Diagnostic mode. Using fast, slow key to select L Er (clear last error) and push Start to clear the error.
Push Stop key , and you are in Stop mode.
Now you are ready to test the treadmill.
Start the treadmill and check the Error message again.
Error 1, Error 2, Error 4, Error 40, Error 41 ?
Check the motor runs or not , when you test it ?
Warning : Do not step on the treadmill, it is very dangerous.
Push Stop + Fast together in setup mode, and you are in
Diagnostic mode. Using fast, slow key to select L Er (clear last error) and push Start to clear the error.
Push Stop key , and you are in Stop mode.
Now you are ready to test the treadmill.
Start the treadmill and check the Error message again.
Error 1, Error 2, Error 4, Error 40, Error 41 ?
Check the motor runs or not , when you test it ?
Warning : Do not step on the treadmill, it is very dangerous.
ERROR 3. Safety key
Check safety key
If it happens frequently. Check safety key cable and switch. - Open the plastic and check.
Next check the signal cable between motor and console. Change the console.
Next check the signal cable between motor and console. Change the console.
ERROR 4. Power circuit trip
Power circuit broken or motor locked or broken.
Do not use treadmill, call service. Fatal error.
It typically happens during workout(8Km /H to 14Km/H).
Do not use treadmill, call service. Fatal error.
It typically happens during workout(8Km /H to 14Km/H).
Check when it happens. During workout (Speed 8Km/H to 14Km/H)? Or when they start the treadmill(Start)?
Turn off and on the power. Push Stop + Slow together, and you are in setup mode. Push Stop + Fast together in setup mode, and you are in Diagnostic mode.
Using fast, slow key to select L Er (clear last error) and push Start to clear the error.
Push Stop key, and you are in Stop mode.
Now you are ready to test the treadmill.
Start the treadmill and check the Error message again.
Error 1, Error 2, Error 4, Error 40, Error 41?
Check the motor runs or not, when you test it?
Warning : Do not step on the treadmill, it is very dangerous.
Turn off and on the power. Push Stop + Slow together, and you are in setup mode. Push Stop + Fast together in setup mode, and you are in Diagnostic mode.
Using fast, slow key to select L Er (clear last error) and push Start to clear the error.
Push Stop key, and you are in Stop mode.
Now you are ready to test the treadmill.
Start the treadmill and check the Error message again.
Error 1, Error 2, Error 4, Error 40, Error 41?
Check the motor runs or not, when you test it?
Warning : Do not step on the treadmill, it is very dangerous.
ERROR 5 – 51 – 52 – 53 Elevat ion
Check incline sensor or motor.
Err 51,Err 52,Err 53 happen during self test or calibration.
Check incline sensor or motor.
Err 51,Err 52,Err 53 happen during self test or calibration.
Turn off and on the power.
Push Stop + Slow together , and you are in setup mode.
Push Stop + Fast together in setup mode, and you are in
Diagnostic mode.
Using fast, slow key to select L Er (clear last error) and push Start to clear the error.
Select tESt (Self test mode)in disgnostic and push Start to test the treadmill. Then elevation goes up to max and go down to min, please check the right side LED.
It should be more than 200 when elevation in max, and it should be less than 50 when the elevation is min.
Check the error message. Error 51, Error 52, Error 53 or no message. Check the elevation motor runs or not, when you test it ?
Warning : Do not step on the treadmill, it is very dangerous. If no error message, Please send the value that is displayed of right side LED during self test to Healthstream R&D center. You have to do calibration again, if you want to use the elevation function. (Diagnostic mode)
Push Stop + Slow together , and you are in setup mode.
Push Stop + Fast together in setup mode, and you are in
Diagnostic mode.
Using fast, slow key to select L Er (clear last error) and push Start to clear the error.
Select tESt (Self test mode)in disgnostic and push Start to test the treadmill. Then elevation goes up to max and go down to min, please check the right side LED.
It should be more than 200 when elevation in max, and it should be less than 50 when the elevation is min.
Check the error message. Error 51, Error 52, Error 53 or no message. Check the elevation motor runs or not, when you test it ?
Warning : Do not step on the treadmill, it is very dangerous. If no error message, Please send the value that is displayed of right side LED during self test to Healthstream R&D center. You have to do calibration again, if you want to use the elevation function. (Diagnostic mode)
ERROR 40 - 41 Over acceleration
Treadmill accelerates too fast than normal.
It happens when the speed is less than 8 Km/H. Fatal error. Stop using treadmill. Power circuit could be broken. Same as Error 40, but it happens at the beginning of workout.( D uring Start)
It happens when the speed is less than 8 Km/H. Fatal error. Stop using treadmill. Power circuit could be broken. Same as Error 40, but it happens at the beginning of workout.( D uring Start)
Check when it happens. During workout (Speed 8Km/H to 14Km/H)? Or when they start the treadmill (Start)?
Turn off and on the power. Push Stop + Slow together, and you are in setup mode. Push Stop + Fast together in setup mode, and you are in
Diagnostic mode. Using fast, slow key to select L Er (clear last error) and push Start to clear the error. Push Stop key, and you are in Stop mode. Now you are ready to test the treadmill.
Start the treadmill and check the Error message again. Error 1, Error 2, Error 4, Error 40, Error 41? Check the motor runs or not , when you test it ?
Warning: Do not step on the treadmill, it is very dangerous.
Turn off and on the power. Push Stop + Slow together, and you are in setup mode. Push Stop + Fast together in setup mode, and you are in
Diagnostic mode. Using fast, slow key to select L Er (clear last error) and push Start to clear the error. Push Stop key, and you are in Stop mode. Now you are ready to test the treadmill.
Start the treadmill and check the Error message again. Error 1, Error 2, Error 4, Error 40, Error 41? Check the motor runs or not , when you test it ?
Warning: Do not step on the treadmill, it is very dangerous.
SPEED ADJUSTMENTS
Speed + and Speed – will adjust speed by increments of 0.1Km/H during workout. Or you may hold these buttons to ramp up or down.
ELEVATION ADJUSTMENTS
For safety reasons, elevation is designed to be manually adjusted only. At no time will treadmill automatically adjust elevation except during one of the following three programs workout: P2 = elevation program, H-SE = HRC by speed and elevation, and H-E = HEC by elevation.
Elevation may be adjusted even while the running belt is not moving. However, during the program setup mode, elevation will not be adjustable.
PULSE FUNCTION
This treadmill features wireless heart rate monitoring, the most advanced technology to date for accurate read out of your heart beat.
To use the wireless pulse monitoring system, you must wear the heart rate transmitter chest strap so that the contact surface is next to your skin directly under your heart to pick up the pulse signals from your heart. There is a heart rate transmitter strap included with this treadmill.
Please note that some fibers used in clothes (e.g. polyester, polyamide) create static electricity which may prevent reliable heart rate measurement. Also note that mobile phone, television and other electrical appliances form an electro-magnetic field around them, which may also cause problems in heart rate measurement.
PAUSE FUNCTION
When STOP button is pressed during workout, program is suspended. After the running belt has come to a complete stop, display will count down from 03:00. During pause mode, only START and STOP buttons will function. If START is pressed within three minutes during the pause mode, treadmill will bring the running belt movement back to the speed at which the treadmill was paused. Workout values will resume counting and continue where it was left off. If STOP is pressed during the pause mode, program will end. After three minutes if no button is pressed, treadmill will automatically end the workout program.
END OF WORKOUT STATS
When you have completed your workout, the display windows will report your workout stats for one minute. After the running belt has come to a complete stop, the displays will show total time, total distance, total calories and average speed. Then the display will go to idle mode, ready for the next user workout setup. If you wish to skip the workout stats report, simply press the STOP button, which will skip display to the idle mode.
UNIT CONVERSION
To change from metric to English or English to metric, you must be in the idle mode. Follow the steps below to make the unit conversion.
1. Simultaneously press both the STOP and SPEED– buttons.
Speed + and Speed – will adjust speed by increments of 0.1Km/H during workout. Or you may hold these buttons to ramp up or down.
ELEVATION ADJUSTMENTS
For safety reasons, elevation is designed to be manually adjusted only. At no time will treadmill automatically adjust elevation except during one of the following three programs workout: P2 = elevation program, H-SE = HRC by speed and elevation, and H-E = HEC by elevation.
Elevation may be adjusted even while the running belt is not moving. However, during the program setup mode, elevation will not be adjustable.
PULSE FUNCTION
This treadmill features wireless heart rate monitoring, the most advanced technology to date for accurate read out of your heart beat.
To use the wireless pulse monitoring system, you must wear the heart rate transmitter chest strap so that the contact surface is next to your skin directly under your heart to pick up the pulse signals from your heart. There is a heart rate transmitter strap included with this treadmill.
Please note that some fibers used in clothes (e.g. polyester, polyamide) create static electricity which may prevent reliable heart rate measurement. Also note that mobile phone, television and other electrical appliances form an electro-magnetic field around them, which may also cause problems in heart rate measurement.
PAUSE FUNCTION
When STOP button is pressed during workout, program is suspended. After the running belt has come to a complete stop, display will count down from 03:00. During pause mode, only START and STOP buttons will function. If START is pressed within three minutes during the pause mode, treadmill will bring the running belt movement back to the speed at which the treadmill was paused. Workout values will resume counting and continue where it was left off. If STOP is pressed during the pause mode, program will end. After three minutes if no button is pressed, treadmill will automatically end the workout program.
END OF WORKOUT STATS
When you have completed your workout, the display windows will report your workout stats for one minute. After the running belt has come to a complete stop, the displays will show total time, total distance, total calories and average speed. Then the display will go to idle mode, ready for the next user workout setup. If you wish to skip the workout stats report, simply press the STOP button, which will skip display to the idle mode.
UNIT CONVERSION
To change from metric to English or English to metric, you must be in the idle mode. Follow the steps below to make the unit conversion.
1. Simultaneously press both the STOP and SPEED– buttons.
2. The message center will display UNIT
3. Simply press START to confirm.
3. Simply press START to confirm.
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment